|
|
|
Elecro Heat Exchangers - Standard Range
The Elecro multi tubular heat exchanger has been designed specifically for the heating/ cooling of all types of pools, and are perfect for use in conjunction with gas or oil fired boilers, solar panels, heat pumps and chillers.
The Elecro heat exchanger is installed inline with the pool filtration circuit, and a heated water circuit. The two independant water circuits flow in opposite directions through the heat exchanger, and the heat is absorbed by the swimming pool water.
Constructed using premium grade materials, the Elecro heat exchanger features a densley populated 'laminar flow' tube stack and low volume heating chamber, which ensures that temperature differentials are optimised, and thus allows for excellent heat transfer performance.
Features:
Polyamide/ Stainless Steel outer shell
Available in either Stainless Steel 316 or Pure Titanium
Fully Dismantlable for easy cleaning/ maintenence
Thermostat Pocket
Supplied with multi position floor/ wall mounting brackets and 1.5" solvent weld unions for connection to rigid pipe work
Includes 1" brass nipples for connection to heating circuit
Constructed using the highest quality materials
114310 |
85,000 btu (25kw) Stainless |
£330.00 |
£259.99 |
Add to basket
|
114312 |
136,000 btu (40kw) Stainless |
£375.00 |
£299.99 |
Add to basket
|
114313 |
238,000 btu (70kw) Stainless |
£425.00 |
£339.99 |
Add to basket
|
114319 |
85,000 btu (25kw) Titanium |
£395.00 |
£319.99 |
Add to basket
|
114320 |
136,000 btu (40kw) Titanium |
£445.00 |
£349.99 |
Add to basket
|
114321 |
238,000 btu (70kw) Titanium |
£485.00 |
£379.99 |
Add to basket
|
114330 |
341,000 btu (100kw) Titanium |
£535.00 |
£419.99 |
Add to basket
|
|
|
|
Heat Exchangers
By utilising a heat exchanger you can create the most economical and efficient way of heating a Koi pond.
Linked to a boiler, the heat is transferred to the pond via the heat exchanger. The final selection of a heat exchanger should be ascertained by pond capacity, boiler output, heat retention properties and positioning of equipment.
The output specification of the heat exchanger is the maximum that may be reasonably expected the unit to produce, so it is therefore highly recommended to upgrade to the next output size if in any doubt.
Example: If you need a 60,000 btu, buy a 100,000 btu.
It is important that the correct rated boiler is used for the size and gallonage of the pond and that the flow rates are not exceeded. The maximum flow rates for the primary and secondary circuits are stated on the label fixed on the front of the boiler along with the relevant rating of that specific heat exchanger.
G M Heat Exchangers are manufactured from quality marine grade type 316 stainless steel.
Each unit undergoes 12 stringent tests during quality control production.
Each unit is tested to 70 p.s.i before leaving the factory and each one is guaranteed for a full 12 months from purchase date, subject to essential conditions are strictly followed during the installation and working life.
All units must be installed vertically. Care must be taken to insure that no chemical residue can enter the heat exchanger when the system is not running. It is recommended to maintain a constant pH between 7.2 – 7.6 to prevent excessive scaling deposits and corrosion.
It is paramount that the unit is installed in an upright position; with the primary and flow connections from the boiler set top and bottom.
The secondary flow, which is the heated flow to the pond (usually after filtration), is then connected to the top right and the flow though which transfers the heated water to the pool will be situated at the lower left outlet. All threaded connections are standard BSP thread.
Note: No Fittings are supplied with these Heat Exchangers, for pressure pipe connections use fitting code (07604).
Sizes and GPH Data:
Heat Exchanger 60,000 btu - Max Gallons 3,000 - Max gph 900 - single coiled
Heat Exchanger 100,000 btu - Max Gallons 5,000 - Max gph 1,440 - single coiled
Heat Exchanger 130,000 btu - Max Gallons 6,500 - Max gph 1,860 - single coiled
Heat Exchanger 170,000 btu - Max Gallons 8,500 - Max gph 2,460 - single coiled
Heat Exchanger 230,000 btu - Max Gallons 11,500 - Max gph 3,300 - single coiled
Heat Exchanger 460,000 btu - Max Gallons 23,000 - Max gph 8,580 - double coiled
|
|
|
Heat Exchanger Fitting
Use this fitting to connect on to the GM Stainless Steel Heat Exchangers
Brass 1" x 22 mm Connector
For use with Single Coiled Units.
This brass fitting is for the primary flow and return to the boiler.
|
displaying results 1 to 3 (of 3 items)
|
|
